Primary tabs

FREE SHIPPINGFree shipping on all orders over 100000 INR.

RO CLEANER 4030

0
No votes yet
SKU::RXSOL-33-3345-260

Product Qty Per Unit: 
260.00
Product usage unit: 
Kg

Negotiate Price

Product Delivery Locations: 
Haldia Port, Kolkata Port Trust, Dhamra Port, Paradip Port
Category: 
RO Chemicals-33
Generic Name: 

RO CLEANER 4030 is a low pH liquid cleaner designed to remove metal foulants such as iron, manganese, and aluminium as well as calcium carbonate scale deposits from spiral wound polyamide and cellulose acetate elements.

Product Description: 

RO CLEANER 4030 is a low pH liquid cleaner designed to remove metal foulants such as iron, manganese, and aluminium as well as calcium carbonate scale deposits from spiral wound polyamide and cellulose acetate elements. RO CLEANER 4030 is made according to  ANSI/NSF Standard 60 for use as an off-line cleaner in drinking water systems.

Product Application: 

Scale deposits remover from spiral wound polyamide and cellulose acetate elements.

Product Procedure: 

Use Instructions:

1. Fill the cleaning tank to the desired volume with RO permeate or DI water. Heat the solution to the maximum acceptable temperature (see membrane manufacturer guidelines) as this will dramatically increase the cleaning efficiency. Add sufficient RO CLEANER 4030  to create a 2% wt/wt solution if the fouling is moderate/severe or 1% if the fouling is mild. Recycle the solution through the cleaning tank to ensure adequate mixing.

2. Recirculate the cleaning solution through each RO system stage, one at a time, for a minimum of 60 minutes at the flow rate recommended by the membrane
manufacturer. If that rate is not known, use the guidelines listed below:

 

Element Diameter, inches

Flow Rate per Vessel, gpm (m3/hr)

4

10 (2.4)

8

40 (9.0)

3. If the membranes are heavily fouled and the recirculated cleaning solution becomes discolored or turbid, discard as much as 15% of the solution volume. Heavily fouled elements may also benefit from a soak period (up to 8 hours).

4. Monitor the pH of the solution during the cleaning process. If the pH remains in the desired range and the solution is not turbid, it may be used to clean subsequent stages. In the unlikely event the pH rises, prepare a new batch and repeat steps 1-4.

5. When the clean is completed, rinse the membranes by recirculating RO permeate through each pressure vessel. To comply with NSF standards, the cleaner should be flushed out with 5 bed/volumes of water before putting the system back on-line.

Product Note: 

PERFORMANCE :

RO CLEANER 4030 offers an array of performance benefits:

  • Compatible with all polyamide and cellulose acetate membranes.
  • Contains a special blend of buffers, chelants, and reducing agents, to promote the dissolution of metal deposits.
  • Superior results to generic citric and hydrochloric acid solutions.
  • Highly buffered to resist pH changes during the cleaning process.
  • Can be used in conjunction with other applicable cleaners to remove combination foulants.
  • Temperature compensated to maintain optimum pH over a wide temperature range.
Product Technical Specification: 

 

Appearance

: Clear, amber liquid

pH (2% solution)

: 2.5 -3.50

Specific Gravity (@25°C)

: 1.35

 

Product pack size: 
30 Kg, 260 Kg and 1350 Kg IBC
Product alias: 
<p> RoClean L403</p>

RO CLEANER 4030 Manufacturer and supplier in Mumbai, Dubai, Muscat, Nairobi, Kenya, Gandhidham, Surat, Chennai, Visakhapatnam, Sharjah, Ajman, Abudhabi, UAE, Ruwi Barka, Sohar, Kolkata, Paradip, Sudan, Yemen

Remarks: