Primary tabs
HCF Remover 210 Ltr
SKU::RXSOL-20-2007-210
RXSOL-20-2007-210 is a very strong low foaming cleaner, Especially formulated to soften up / remove baked on drying oils and also used after animal and vegetable oils, fish oils, tall oils,tug oil etc. It is low toxic product with an exceptional solvency power on soil & oily matter. It is free from hydrocarbon solvents and minimizes the extreme hazards to personnel in handling materials.
Powerful solvency
Moderate evaporation rate
Low viscosity
High dilution ratio
Low surface tension
Coupling ability
Wide range of applications
First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-2007-210 is by direct injection followed by recirculation washing, using tank cleaning machines.
RXSOL is HCF remover manufacturer and supplier. We are keeping ready stock of this materials at our following location - Mumbai, Sikka, Mundra, Kandla, Gandhidham, Surat, Hazira, Pirpav, JNPT, Goa, Manglore, Kochin, Vizag - Visakhapatnam, Gangavaram, Ennore http://rxmarine.com/kamarajar-port-ennoreport , Chennai, Fujairah, Dubai, Sharjah, Abu Dhabi, Middle East. We have our distributor and agent for supply of HCF remover in Istanbul, Turkey.
For export of HCF remover we are very popular due to its cost effectiveness.
Using-Procedure:-First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-2007-210 is by direct injection followed by recirculation washing, using tank cleaning machines.
Spraying Method:-Using HCF as delivered in drums, spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butterworth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages. Inspects tanks(s) and if desired result has been achieved fresh water rinse and dry.
** Make sure to take all safety precautions are followed when handling / spraying HCF **
Injection Method:– Prepare 0.1-0.5 % cleaning solution with fresh water, leave the solution on the surface for 5-10 minutes than wipe away. Heat the solution to get better results up to 60°C. It is not corrosive so it can be used on every surface.
Re-circulation Method:–Fill tank with fresh water and heat up to warm 50oC . IF a drop line is available on the tank line system, then start to circulate the water and add the required amount of Caustic flakes and HCF to make a 2.5% solution. A stronger solution can be made, but be advised that too much Caustic and too high temperature will result in white powder all over the tank. Under normal circumstances, between 2.5% and 4.5% will be sufficient strength. If there is no drop line, then lower butterworth hoses into the tank from the pump stack header without machines attached and circulate through these hoses while you fill the solution material.
OR
Recirculation Method: Prepare 0.1-0.5 % cleaning solution with fresh water and circulate or spray with water jets to clean contaminated tank surfaces. Recirculate at least 3-4 hours around 30-60 °C. The solution can be re-used until it is no longer effective. After circulation make the test and rinse the tank with fresh or DI water depending on the next Cargo. For Veg-Palm Oil Cleaning : Circulate the tank with cold sea water 1.5 hours, than circulate the tank with hot sea water (50-60 o C ) for 1.5 hours. Finally, circulate the tank with HCF REMOVER 1 (One) hour around 40-50 C.
Spot Cleaning: Depending upon the contamination, HCF REMOVER should be sprayed undiluted or diluted between 0.1-10% and allowed to soak on the area for 20 – 30 minutes. Finally, rinse the tank with plenty of hot fresh water around 30-40 minutes. For small residues and for last Hydro Carbon Free issues, usage will be around 0.1%. Afterwards tanks must be washed down with plenty of fresh water. For cleaning tuff cargo residues prepare a solution 5-10 % with hot fresh water and apply same procedures with spot cleaning. While cleaning and rinsing the tank surfaces, the efficiency of the solution can be increased by using warm water up to 60°C.
**Use a strainer at the pump stack when circulating any solution.**
Tank Lining– Stainless / Epoxy / Phenolic / Zinc-silicate.
Characteristics: -
- Removes grease, oil, carbon deposits, soil and grime.
- Keeps loosened deposits in suspension preventing re-deposition.
- Low toxic. , Non-flammable.
- Free from hydrocarbon solvents.
- Effective and economical in use , Water-based cleaner.
- RXSOL-20-2007-HCF has numerous cleaning applications including removal of greases, waxes, oil, sludge, soot, carbon deposits and general dirt and grime.
- Non-corrosive to ferrous metals. Suitable for all tank-coatings.
- Can be used for gas and hydrocarbon freeing of tanks.
- Can be used for deodorizing
-
Contains wetting agents.
Note:- Completely miscible with sea water.
HCF Neutral cleaner (HYDROCARBON FREE) is a powerful concentrated tank clean detergent. HCF cleaner is non-flammable heavy duty non-solvent and water-based new generation tank cleaner. Non–toxic, surfactants blend in HCF neutral makes it an ideal solution for removing all vegetable and animal fats and oils, and light mineral oils from tank surface.
HCF Cleaner, as well as HCF REMOVER, plays a very important role in tank cleaning operation. Due to its higher percentage surfactant value, all residue gets easily dissolved.
HCF REMOVER is a highly concentrated natural based cargo tank cleaner with a neutral pH. It is free from chlorinated/aromatic hydrocarbons, caustic and alkalines. It can be used for the cleaning of palm oil, vegetable oil, fish oil and soybean oil from cargo tank surfaces.
HCF REMOVER tank cleaning marine chemicals supplier in Mumbai, Pirpav, JNPT, Mundra, Kandla, Sikka Jamnagar, hazira, Kolkata, Haldia, Paradip, Chennai, Ennore, Karaikal, visakhpatnam, Manglore INDIA, Fujairah, Sharjah, Dubai, Ajman UAE Middle East, Sohar, Muscat OMAN Barka, Canada
Tank Lining– Stainless / Epoxy / Phenolic / Zinc-silicate.
